Products
Expertise by Industry
Case Studies
Knowledge
Sample Pumps
The O1608-16 sample pump is a low head submersible filterpump with an integral self-cleaning filter for use with on-line analysers and dosing systems. It delivers a filtered output of water which prevents blockage to nozzles, valves and solenoids. Sample water can be screened to 60 microns and pumped simultaneously.
Key Features
Sample Pumps
Specifications & Dimensions
Specification
Dimensions
Prices & ordering
- All Models
- O1608
- O25010 60 Hz
- Flint 480
Similar Products
Omnia
Our Omnia range low head submersible pumps have a maximum output of 220 litres/minute and a maximum head of 1.1 bar. They have single phase motors and integral self-cleaning suction intakes and are ideal for sampling and small open loop heat pump systems.
- Maximum Output 220 L/ Min, 45 US GPM
- Maximum Head 11 m, 25 ft
Price from: £1,970
Flint
Our Flint filterpumps are our 60 Hz robust low head submersible pumps with an integral self-cleaning suction intake. Built with wear-resistant rubber and ductile iron for durability, they have a maximum output of 79 US GPM, maximum head of 54 ft.
- Maximum output - 79 US GPM, 300 l / min
- Maximum head - 54 ft, 16 m
Price from: £0
General Information Filterpumps for Sampling
Our smaller filterpumps, Omnia, Flint and Idrogo ranges, are used widely in the water industry and beyond for raw and dirty water sampling for analysis. These are submersible centrifugal pumps with integral self-cleaning suction intakes that can screen and pump water simultaneously.
These pumps are preferred for raising sample water because they can screen down to 60 microns without blocking. Because water is filtered as it is pumped from source, analytical equipment is protected against clogging and blocking by any debris or particulate that may be in the sample water.
Here are some of the uses we have our sample pumps for:
- screening and supplying sample veg and salad washing water for dosing systems
- Protecting sampling equipment at raw water intakes
- Screening and supplying final effluent for analysis at waste water treatment works
- Ensuring low-maintenance continuous monitoring at remote and unmanned sample sites
Rotorflush Omnia sample filterpump fitted with sintered stainless steel intake screen, built in float switch and small stand.
Sample filterpumps can be fitted with:
Nylon Mesh inserts
The filter mesh is made up of replaceable bias-cut nylon mesh offering a very clean filtration, ideal for sampling. The inserts are inexpensive and easy to replace.
Available in 60 micron, 115 micron or 300 micron.
316 Stainless Steel Sintered Mesh
A robust screen that can be easily cleaned with a pressure washer. Ideal for heat pumps and other application with small tolerances.
Available in 50 micron, 100 micron and 315 micron.
Due to their small size and portability, our sample pumps are very versatile and can be installed in a number of ways.
The key thing to remember is to make sure that they have a lot of clear space around the mesh for the back-washed debris to be dispersed into, and that they are not sitting in a build-up of silt or sludge.
Sample pumps can be suspended in water, hung from a float, or if the water conditions allow, placed in water on a stand.
We also manufacture stands and guide rails to help site your filterpump.
Rotorflush submersible self-cleaning intake sample pump on a guide rail
Although they are self-cleaning all of our products will require a manual clean every once in a while.
The nylon mesh inserts are easily replaced and stainless mesh can be cleaned with a pressure washer. How often depends on your mesh size and what you are filtering.
As a minimum we recommend the following:
- Mesh up to 115 micron should be cleaned or replaced every 1000 hours of use
- Mesh up to 315 micron should be cleaned or replaced every 5000 hours of use
Full maintenance guidelines can be found in the instruction manuals available from the download link above.
All our products are guaranteed for a year. Full details in our Terms and Conditions below.
Why Rotorflush?
UK Designed & manufactured
Talk to our friendly team of engineers to discuss your design requirements.
- Built to your water output
- Filter down to 50 microns
- Hand built in the UK
Leading water filter experts
Talk to our friendly team of engineers to discuss your design requirements.
- Industry experts for over 20 years
- 1000's in use worldwide
- Successfully deployed screening 10 - 7,225 US GPM
- Keeping water flowing and pumps, screens, spray bars and other equipment working
Worldwide delivery and service
Through our worldwide distribution network we offer the ability to:
- Deliver filterpumps worldwide
- Help service your filterpump
- Repair broken filterpumps
Talk to an expert about your project
Call us now on 01297 560 229 | 8am - 5pm UK time
Or leave us a message and a member of our expert, friendly team will call you back and will find the filter pump for your needs.
- We work with you to identify your issues
- We can design & build a custom solution
- We can deliver our solution worldwide
Find out more or tell us your choice of sample pump
Get the filterpump your project requires, talk to our friendly team
This website uses cookies to ensure you get the best experience. Learn more